Shotgun Big Dot Tritium Front Sight Xs Sight Systems.
Installs Easily Over The Existing Bead Sight
Highly visible, tritium dot front sight surrounded by a large white ring epoxies over the existing front bead sight to help improve target focus and low light sight acquisition and sight recovery after muzzle flash. Installs over front sight beads from .125" - .140" diameter by filling the cavity on the underside of the sight with Brownells Acraglas Gel, then pressing the sight over the bead and allowing it to fully cure. If existing bead is too small or too large, replace with Brownells #6 bead for 3-56 threads or #26 for 6-48 threads. Some shotgun barrels may require drilling and tapping of existing hole to 6-48 for installation of #26 Brownells bead. Remington Pedestal model with stepped bottom fits Remington shotgun barrels with front sight pedestal. Vent Rib model with flat bottom fits shotgun barrels with ventilated ribs. Plain Barrel model with cupped bottom fits round shotgun barrels. Includes instructions.
Big Book Catalog, Issue:71, Page:313
Fiber Optic Front Sights Red Novak.
Maximizes Available Light For Fast, Low-Light Sight Acquisition
Advanced light gathering properties of fiber optic rods make maximum use of ambient light to provide a bright glow that stands out against dark backgrounds and puts you on target fast, even in low-light or high-stress situations. Fronts and rears sold separately, so you can create a custom, three-dot, fiber optic system tailored to your shooting needs. Available with red or green inserts. Front sight can also be used with Novak’s plain, wide-notch rear. Kimber and Taurus front sights are the same height as factory sights and fit factory dovetails; no machining required.
1911, Issue:11, Page:045
Big Book Catalog, Issue:71, Page:138
Sinclair, Issue:1A, Page:042
SPECS: Machined steel, matte black finish with fiber optic rods in red or green. Colt – Front: Blade is .64" (1.6cm) long, .127" (3.2mm) wide. Fits Government model; milling required, instructions included. Kimber - Front: Red insert. Blade is .650" (16.5mm) long, .125" (3.2mm) wide. Available in .150" (3.8mm) and .175" (4.4mm) heights. Fits factory dovetails of Kimber 1911 pistols; minor fitting may be required. S&W – Front: Blade is .47" (1.19cm) long, .127" (3.2mm) wide. Fits Government and Commander models. Taurus – Front: Red insert. Blade is .66” (1.7cm) long, .123” (3.1mm) wide, .150” (3.8mm) high. Fits Taurus 1911 pistols; minor fitting may be required.
Red M&p Shield Action Enhancement Trigger Apex Tactical Specialties Inc.
The Shield Action Enhancement Trigger Kit directly replaces the factory hinged trigger with a red anodized, solid aluminum trigger body which reduces pre-travel and over-travel by approximately 20%. It features a smooth face with a center mounted pivoting safety that maintains factory safety values. The center mounted pivoting safety bar prevents unintended operation by creating a trigger block that will not disengage unless the shooter places their finger directly on the trigger face.
The Apex Shield Duty/Carry Kit was designed to provide the M&P Shield pistol owner a smooth, consistent trigger pull that is approximately 2 lbs lighter(based on variations in factory tolerances) with the advantages of shorter over-travel and more detectable trigger reset. The kit itself is engineered to be drop-in and should not require further gunsmithing. However, Armorer or gunsmith installation of the Ultimate Striker Block into the Shield slide is strongly recommended.
The Shield Action Enhancement Trigger Only is perfect for use with the M&P Shield already equipped with the apex Shield Duty/Carry Kit. Works with all Smith & Wesson M&P Shield pistols in 9mm and .40 calibers, does not work in the Shield 45.
Big Book Catalog, Issue:71, Page:233
SPECS: Kit includes: Red Anodized Aluminum Shield Action Enhancement Trigger, Shield Duty/Carry Kit(Fully machined sear, Ultimate Striker Block, Striker Block Spring, Sear Spring(1/8"), 4lb rated Trigger Return Spring, Trigger Return Spring Installation Shield Slave Pin, Talon Tactical Tool). Trigger Only includes: Red Anodiezed Aluminum Shield Action Enhancement Trigger, Shield Trigger Return Spring Installation Slave Pin.
Ar-15 M4 Stock Wrench Rock River Arms.
Install M4 Carbine Stocks Without Damage
Steel, dual function wrench lets you easily remove your old extension tube and install a new-style, A4 stock. Spanner has three lugs to fit the A4-style castle nut. Provides a non-slip fit so you can hand tighten the castle nut to the receiver. Also, the comfortable, rubber coated handle features a cutout to fit the receiver extension tube to remove the A1 or A2 stock.
AR-15, Issue:11, Page:083
Big Book Catalog, Issue:71, Page:086
SPECS: Steel, parkerized finish. 7-5/8" (19.3cm) long.
Heat-Treating Charcoal Brownells.
Produces Dramatic Color & Swirl Patterns
Wood and bone charcoal with just the right sieve size for crucible packing of steel parts to be hardened. Hi-carbon content without waxes or fillers gives brilliant color patterns. Mixing types by specific ratio provides additional control over color and pattern.
These items cannot be shipped to Australia.
Big Book Catalog, Issue:71, Page:384
Big Book Catalog, Issue:71, Page:398
SPECS: Packed in 5 gal. bucket. Bone - 10x28 sieve size, 25 lb. (11kg) weight. Wood - #6 size. 10 lb. (4.5kg) weight.
Bubble Levels Vortex Optics.
For the most precise long-range shooting, use the bubble level to ensure that the rifle is perfectly vertical. This will eliminate potential error caused by shooting a canted rifle.
Mounts quickly and easily to the riflescope tube.
Sinclair, Issue:5B, Page:212
Ar-15/m16 5.56 Bolt Assembly Daniel Defense.
Steel bolt is shot-peened for extra surface hardness, then magnetic particle inspected (MPI) for cracks and flaws to ensure reliability and long service life. Models available for rifles chambered in 5.56mm/.223. Comes completely assembled, with gas rings, extractor, and ejector installed.
AR-15, Issue:11, Page:012
Big Book Catalog, Issue:71, Page:012
SPECS: Carpenter 158 steel, phosphate coated, matte black.
Ak-47 Aluminum Akg2 Side Mount 1-Piece Tactical Base Midwest Industries, Inc..
Mount Optics Securely to Your AK-47
When it comes to mounting optics, the AK platform isn't known for its ease of accessory mounting. Even optics that are mounted successfully aren't always able to maintain zero, due to poor-quality mounting accessories. End your troubles with the Midwest Industries AKG2 Side Mount Tactical Base.
- Made from durable aluminum
- Features hard-anodized black finish
- 1-piece design
The solid design of the Midwest Industries AKG2 Side Mount Tactical Base ensures that users can mount a wide variety of optics on their AK-style rifle and maintain zero, even in rugged conditions.